| Brick Bolsters |
| Designed specifically for cutting bricks smoothly and cleanly. |
|
| Sizes range from: |
| 50mm x 19mm to 112mm x 25mm |
| Brick Hammer |
| This tool is used by bricklayers for cutting and cleaning bricks and masonry. |
|
| Brick Rakes |
| Used by bricklayers for raking out fresh mortar to create a raked joint between bricks. |
|
| Size: 300mm |
| Centre Punches |
| Used for marking out prior to drilling. |
|
| Sizes range from: |
| 100mm x 9mm to 200mm x 19mm |
| Club or Lump Hammer |
| A standard and essential tool for all builders |
|
| Sizes: |
| 2.5 lb and 4 lb |
| Cold Chisels |
| Used for cutting steel, and by the building trade for chopping holes into brick and stone. |
|
| Sizes range from: |
| 100mm x 6mm to 1200mm x 25mm |
| Corrugated Iron Punch |
| Used to punch holes in corrugated iron sheet. |
|
| Size: |
| 200mm x 13mm x 8mm |
| Dooking Chisels |
| Designed to cut holes through stone and brickwork. |
|
| Sizes: |
|
300mm x 16mm x 19mm 350mm x 16mm x 19mm 450mm x 19mm x 25mm |
| Double Ended Scutch Hammer |
| Used by the building trade for dressing and cleaning brick and stone. |
|
| Wrecking Bars |
| Multifunctional tools used mainly for prising and levering, drawing large nails and demolition work. |
|
| Sizes range from: |
| 300mm x 13mm to 900mm x 25mm |
| Socket or Deck Scrapers |
| Originaly used by the maritime industry for scraping the decks of ships and boats. They are now used to clean hardened debris from any type of floor |
|
| Sizes: |
| 100mm - 125mm - 175mm |
| Scutch Chisels |
| Designed to hold a detachable stone dressing comb or drove. The tool is then used to dress stone and brickwork. it has also proved very effective when fitted with a scutch comb for cutting into hard bricks and block to fit socket boxes |
|
| Sizes: |
| 25mm - 37mm - 50mm |
| Electrician's Bolster / Flooring Chisels |
| Generally used by electricians for cutting the tongue in tongue and grooved floorboarding, requiring a flexible blade to give sufficient leverage to raise a floorboard enough to insert a lever bar. |
|
| Size: |
| 225mm x 56mm |
| Special Chisels |
| Crosscut chisels are used for cutting keyways, Halfround chisels for cutting oil grooves and Diamong point chisels for squaring out corners in keyways and cutting V shaped grooves |
|
| Slater's Hammer |
| This is a versatile tool used by roofers to knock nails in, remove nails, and punch holes through slates ready for nailing. |
|
| Extended Bolster |
| The longer 450mm electricians dispenses with the need for a lever bar. |
| Size: |
| 450mm |
| Groovedd Plugging Chisels |
| Designed for removing the mortar from between bricks and blockwork to insert a plug for nailing and screwing. The fluted blade is to remove the waste |
|
| Size: |
| 250mm |
| Slater's Ripper |
| Used by roofers for cutting nails and removing slates without damaging the surrounding slates. |
|
| Size: |
| 750mm |
| Line Pins |
| These are used with builder's lines for marking out positions, and setting and aligning courses of bricks. |
|
| Size: |
| 150mm |
| Mason's Chisels |
| Generally used by stone masons for cutting and dressing stone. |
|
| Sizes: |
| 25mm - 31mm - 37mm |
| Mason's Nickers or Bolsters and Pitchers |
| These tools are generally used for cutting and dressing stone. |
|
| Sizes: |
| 50mm - 63mm - 75mm |
| Mason's Points and Punches |
| For forming channels, grooves and lines into stone. |
|
| Sizes: |
| 6mm and 9mm |
| Parallel Pin Punch |
| Used for removing parallel pins. |
|
| Sizes range from: |
| 100mm x 1.5mm to 150mm x 6mm |
| Podger Bars |
| These are used by steel erectors for aligning bolt or rivet holes. |
|
| Size: |
| 450mm x 16mm |
| Scutch Combs and Droves |
| Designed to be fitted into a scutch chisel, both edges can be used until worn and then disposed of. |
|
| Sizes: |
| 25mm - 37mm - 50mm |
![]() |
|||||||||||||
![]() |
![]() |
![]() |
|||||||||||